CD-Recorder Manufacturers

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Note: This information is provided without any warranty and may not be complete. All names may be trademarks or registered trademarks of their respective owners. If your CD-Recorder is not listed, you can simply try. If your writer is listed, please check for required firmware.

This list assumes CloneCD Version 3.x and CCDDriver.dll Version 3.0.0.11

Back to Hardware Requirements

Supported CD-Recorders "W" (23 April 2001)

Waitec
Wearnes

Waitec

CD-Writer	Firmware / Comment	Best Supported Write Mode	Buffer under run Technology	Correct EFM encoding of regular bit patterns	Best supported Read Mode for Data	Best supported Read Mode for Audio
WT2036EI (Atapi)	-	RAW-DAO 16	-	-	RAW	RAW
WT2422EI (Atapi)	-	RAW-DAO 16	-		RAW	RAW
WT2444EI (Atapi)	-	RAW-DAO 16	-		RAW	RAW
WT3244EI (Atapi)	-	RAW-DAO 16	-		RAW	RAW
WT2082 (SCSI)	Rev.>= 1.04	RAW-DAO 96	-	-	RAW+96	RAW+96
WT3284EI (Atapi)	Rev.>= 1.07	RAW-DAO 96	-	-	RAW+96	RAW+96
Shuttle (Atapi)	-	RAW-DAO 16	-		RAW	RAW
T-Rex (Atapi)	Rev.>= 5.32	RAW-DAO 96		-	RAW+96	RAW+96
T-Rex (SCSI)	Rev.>= 4.31	RAW-DAO 96		-	RAW+96	RAW+96

Back to Top

Wearnes

CD-Writer	Firmware / Comment	Best Supported Write Mode	Buffer under run Technology	Correct EFM encoding of regular bit patterns	Best supported Read Mode for Data	Best supported Read Mode for Audio
CDRW-622 (Atapi)	-	RAW-DAO 16	-	-	RAW	RAW

Back to Top

Legend:

Firmware:

If nothing is specified, any firmware version will work. However, the newest firmware version available is recommended.
Rev. >= X.X : Firmware version X.X or better is required
Rev. = X.X : The exact Firmware version X.X is required. Any other version WILL NOT WORK.

Best Write Mode:

RAW-DAO 96 = 2352 bytes RAW Data + 96 Bytes P-W Subchannel Data. This is the best mode for CloneCD. It allows writing of all subchannel information, including Digital Signatures, CD-Text, ISRC, Catalog Numbers, CD+G, CD+Midi, Gaps, Indices and Crazy TOCs.
RAW-DAO 16 = 2352 bytes RAW Data + 16 Bytes P-Q Subchannel Data. This is the second best mode for CloneCD. It allows writing of most subchannel information, including most Digital Signatures, ISRC, Catalog Numbers, Gaps, Indices and Crazy TOCs.
RAW-SAO = 2352 bytes RAW Data. This is the third best mode for CloneCD. Feature support is drive dependant. ISRC, Catalog Numbers and Indices can be written. Usually CD-Text, CD+G and CD+MIDI can be written as well. Crazy TOCs and Digital Signatures can't be written in this mode.
SAO = 2352 bytes error corrected Data. This is the worst mode for CloneCD. Writing of ISRC, Catalog Numbers, Indices and usually CD-Text is supported.
- = Writing to this drive is not supported. CloneCD will not recognize the drive as a CD-Recorder.

Buffer under run Technology:

= Drive offers a buffer under run technology like BurnProof or JustLink. This option can be controlled by the user.
= Drive offers Seamless Link buffer under run technology. Seamless Link is always enabled and can not be switched off.
= Drive offers a buffer under run technology, but the current CloneCD version does not support this feature yet. It is very likely, that this feature will be supported in the future.
= Drive offers a buffer under run technology like BurnProof or JustLink, but this option does not work with CloneCD RAW writing and MUST be turned off!
- = Drive does not offer any buffer under run technology

Correct EFM encoding of regular bit patterns

= Drive writes regular bit patterns correctly
- = Drive does not write regular bit patterns correctly

Best Read Mode:

RAW+96 = 2352 bytes RAW Data + 96 Bytes P-W Subchannel Data. This is the best mode for CloneCD. Reads all subchannel information like ISRC, Catalog Numbers, CD+G, CD+MIDI, Gaps, Indices, Digital Signatures.
RAW+16 = 2352 bytes RAW Data + 16 Bytes P-Q Subchannel Data. This is the second best mode for CloneCD. Reads most subchannel information like Gaps, Indices and most Digital Signatures.
RAW = 2352 bytes RAW Data. No Subchannel Data can be read.
- = Reading from this drive is not supported.